spi devkit

SPI Development Kit

TP120212

The SPI Development Kit is a comprehensive and cost-effective kit that bundles together a complete set of Total Phase’s industry-leading SPI development tools and popular accessories. Both beginners and advanced developers will appreciate the convenience and value of the kit for developing and debugging an SPI bus on an embedded system.

With this kit, developers can exercise target SPI devices, simulate an SPI master, program and verify SPI-based Flash devices, and passively monitor an SPI bus in real-time with bit-level timing down to 20 ns.

Key Features
Cheetah SPI Host Adapter
  • SPI master at up to 40+ MHz
  • Transaction queuing for maximum throughput
  • Pipelined architecture for gapless shifting
  • Precise timing and user-insertable delays
  • Supports up to 3 slave selects
  • Flash/EEPROM programming; in-system or stand-alone
Beagle I2C/SPI Protocol Analyzer
  • Non-intrusively monitor SPI up to 24 MHz†
  • Bit-level timing down to 20 ns resolution
  • Real-time data capture and display – Watch SPI packets as they occur on the bus
  • View SPI protocol-level decoded data packets and SPI-specific error code values
  • View all the bytes from the transaction in Data pane
  • Nearly limitless capture – Captured data is streamed via High-speed USB directly to your computer† Actual SPI capture performance is dependent on CPU speed and SPI bus throughput. 24 MHz SPI capture has been tested for typical applications (e.g., captures of a few hundred SPI packets). Depending on user configuration, the maximum achievable capture throughput for continuous streaming applications may be less than 24 MHz.
High-Speed SPI Flash Demo Board
  • Provides known working SPI Flash memory for testing and debugging purposes.
  • Target SPI Flash Memory: M25P32 32 Mbit, Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface (Numonyx)
  • Easy connection via a 10-pin socket

Tech Specs

Product Specs

Beagle I2C/SPI Protocol Analyzer
Target Bus/Data Monitoring
  • I2C: Up to 4 MHz
  • SPI: Up to 24 MHz
  • MDIO: Up to 2.5 MHz
Host Bus Interface
  • USB 2.0
  • Type-B receptacle
Target Bus Cable
  • 10-pin ribbon cable
  • 1.27mm (0.05″) pitch
  • 130.175 mm (5 1/8″) length
Target Bus Connector
  • Type: 2×5 IDC female, 2.54 mm (0.10″) pitch
  • Pinout
    • Power Pins: GND (Pins 2, 10), NC/+5V (Pins 4,6)
    • I2C Pins: SCL (Pin 1), SDA (Pin 3)
    • SPI Pins: MISO (Pin 5), SCLK (Pin 7), MOSI (Pin 8), SS (Pin 9)
    • GPIO Pins: 1, 3, 5, 7, 8, 9
DC Characteristics
  • Target Power: +5V, 25 mA max
  • I2C/SPI/MDIO Signal: 3.3V, 10mA
Operating Temperature
  • 10 to 35 degrees C (50 to 95 degrees F)
Cheetah SPI Host Adapter
Bit Rate
  • SPI Master: 0.1 MHz – 40+ MHz
Target Bus Interface
  • SPI Master
Host Bus Interface
  • USB 2.0
  • Type-B receptacle
Target Bus Cable
  • 10-pin ribbon cable
  • 1.27mm (0.05″) pitch
  • 25.4 mm (1″) length
Target Bus Connector
  • Type: 2×5 IDC female, 2.54 mm (0.10″) pitch
  • Pinout
    • Power Pins: GND (Pins 2,10), NC/+5V (Pins 4,6)
    • SPI Pins: SS2 (Pin1), SS3 (Pin 3), MISO (Pin 5), SCLK (Pin 7) MOSI (Pin 8), SS1 (Pin 9)
DC Characteristics
  • Target Power: +5V, 25 mA max
  • I2C/SPI/MDIO Signal: 3.3V, 10mA
Operating Temperature
  • 10 to 35 degrees C (50 to 95 degrees F)

What's Included

Hardware
  • Cheetah SPI Host Adapter
  • Beagle I2C/SPI Protocol Analyzer
  • High-Speed SPI Flash Demo Board
  • (2) 6ft USB-A to USB-B Cables
  • (2) 10-Pin Split Cables
  • One Year Warranty
Software (web downloads)
  • Control Center Serial Software
  • Flash Center Software
  • Data Center Software
  • Cheetah Software API
  • Beagle Software API
  • Cheetah LabVIEW Driver
  • Beagle LabVIEW Driver
  • USB Drivers
  • Linux USB Hot Plug Configuration files

System Requirements

Minimum Hardware Requirements
  • Intel or AMD processor operating at 2 GHz or faster
  • 1 GB physical RAM (32-bit) or 2 GB RAM (64-bit)
  • 2 GB or more available hard disk space
  • Full-speed USB port
  • VGA capable of 1024-x768 or higher screen resolution
  • Internet access is helpful
Available Software
  • Control Center Serial Software
  • Flash Center Software
  • Data Center Software
  • Cheetah Software API
  • Beagle Software API
  • Cheetah LabVIEW Driver
  • Beagle LabVIEW Driver
Required Software (Windows & Linux)
  • USB Drivers
PC Requirements & Supported Operating Systems
  • Windows: 7, 8, 8.1, 10
  • Linux: Red Hat, SuSE, Ubuntu, Fedora
  • Mac OS X: 10.7 – 10.14

Dimensions and Quality

Dimensions and Weight
  • (W x D x L) 55.6 x 22.2 x 89 mm (2.19″x0.87″x3.5″)
  • 64 g (0.14 lbs)
Quality
  • CE
  • RoHS
  • One Year Warranty
  • Manufacturing
    • ISO 9001
    • ISO 13485
    • AS9100C
    • ITAR

Your trusted semiconductor supply chain partner

Contact Us